LotusElan.net Unified Search
Search results for: cam cover gaskets in category "Mods"
13 results found containing all search terms.
Sorted by relevance / Sort by date
ARP make studs - just ordered a set to try - but getting the head off may be an issue as the studs will have ...
... forced induction on a Twin Cam rgh0 wrote: ARP ... chain guide in the front cover Rohan, ARP studs ... head on the bock/gasket and screwed the studs ...
And also: http://www.fordracingparts.com/parts/pa ... ield=12142 The legendary Formula Ford Kent block is reborn with an all new iron casting that is stronger than the original! ...
... crankshaft thrust bearing inserts Includes cam bearings US $1299.00 ... Superchargers Timing Drive Related Valve Covers Valves / Springs Exhaust ... ToolsFender Covers Signs Tools VehicleFord Racing PacksPower Packs Handling Packs ...
Hi all I am currently working on a turbocharged twin cam Spec as follows 1900cc , steel 82mm crank, 5.23 BD n/j rods, JE forged ...
... forced induction on a Twin Cam Hi all I am ... chain guide in the front cover cheers Rohan rgh0 ...
I'm starting to get serious about a new engine for my S2 SE DHC street car that hasn't been on the road in over 20-years. ...
... 3500 for head fixings including cams, valve seats, ... inch interference between the bonnet cover and the forward edge ... ample material for the head gasket to seal in all ...
hi guys, john i think my gearbox is the bullet type? looking at the lotus workshop manual it appears to be the original box, do ...
... OR use a Lotus Twin Cam Clutch and replace the ... a lightweight flywheel, clutch cover and clutch plate. ... I replaced the seals and gasket in the diff and ...
Thanks Simon. I like your float level method. I think it's the same level for the 151's? Greg Z
... flat spot with the sprint cams, 32mm chokes and ... have to take off the cover to adjust but you ... used silicone sleeving as a gasket around the outside of ...
7. Engine Dilemma : Mods by LotusElan.net [Mods]
I have a big dilemma, when I started my journey I accepted that I would accept sensible mods that enhance the car and not to ...
... top on spacers to the cam cover and keep it ... the office as a coffee table to preserve it in ... I even re-used the head gasket, it rattled like ...
I have done many of the mods suggested in this post with good results. Three that I do not see are: 1. Oil pressure fail ...
... it. Sometimes make twin cam noises too. Steve ... has sold enough parts to cover the header replacement and ... to pull off th e gasket for the boot. ...
9. Zetec conversion : Mods by LotusElan.net [Mods]
Having just got a 2.0ltr Blacktop zetec of Ebay, and a Retro Ford alternator mounting system and RWD sump too. I was wondering what else ...
... than the original angle. Cam belt has to come ... didnt have a thermostat or cover so ill need to ... , Radiator, I have a Clive boy rad with ...
Hi Aussie John Sorry I didn't clarify things earlier. I do have a sprint with a modded Type 9 box fitted and it works fine ...
... being used in your Twin Cam engine and size of ... and which clutch plate/cover combination should I use ... tomorrow. Hoping some additional gaskets get here tomorrow, ...
Couldn't find a lot in the forum regarding this conversion. My Sprint is currently not running extremely well. And before investing more time and money ...
... smooth power curve for the cams I'm running and a ... ECU, Most people have covered the steps. But ... can give a back to back comparison standard sprint vs ...
Hal, I used the standard S4 air box and trunking. I used Jenvey trumpets but I had to turn the O/D down to make the ...
... , with the original twin cam, the rear section ... they foul of the front cover fixings. I would ... the pump outlet cap and gasket. Andy at Axminster ...
13. Bike Carbs on S4 : Mods by LotusElan.net [Mods]
AAE2901A-5731-4CA4-9EA7-19606DC8B041.jpeg BEA7D67D-CDF9-4A00-85B5-58A18A9E30CB.jpeg A010E78A-32F7-47D3-982B-27A5970149DE.jpeg Fitting of Kawasaki ZX9R carbs to 2 Litre Zetec Silvertop Dunnell 185Bhp engine to replace 45 Spanish Webers and Dunnell ECU. Purchased ...
... blanks. Sits near the cam cover. The blanks ... removed and the normal Carbtune hose tails are screwed in ... and stainless clips. New gasket £15. I ...
Search took 0.160 seconds