Removing suspension bushes

PostPost by: JonB » Thu Jan 18, 2018 4:20 pm

Hi

Quick Q: How hard is it, generally, to remove wishbone and front suspension arm bushes? I don't have a press, just a fat screwdriver and a big mallet..
User avatar
JonB
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 2396
Joined: 14 Nov 2017

PostPost by: Concrete-crusher » Thu Jan 18, 2018 4:27 pm

Hard unless you use a press or maybe a vice and some sockets

Steve
Concrete-crusher
Third Gear
Third Gear
 
Posts: 402
Joined: 09 Jun 2013

PostPost by: john.p.clegg » Thu Jan 18, 2018 5:53 pm

..or a hole saw,( for the rubber )followed by a hacksaw.( for the outer shell ).

John :wink:
User avatar
john.p.clegg
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 5744
Joined: 21 Sep 2003

PostPost by: MarkDa » Thu Jan 18, 2018 7:05 pm

Last lot of fronts I couldn't shift with threaded rod and coupling length nuts; when pressed out a garage it took 10T before they came out!
Well worth a trip and ?5 to save all that hacksawing and wrestling in my book.
MarkDa
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 1215
Joined: 15 Apr 2017

PostPost by: Briggs1 » Thu Jan 18, 2018 7:51 pm

Heat (propane torch) to remove the rubber. Hack saw blade to remove the outer ring. Begin very gentle with the hacksaw . I have been able to get most of the way through them and then grab one side with vise grips and twist the outer sleeve so it peels apart at the hack saw line. Not terribly difficult or time consuming.
Briggs1
Third Gear
Third Gear
 
Posts: 276
Joined: 17 Jun 2004

PostPost by: 661 » Thu Jan 18, 2018 9:02 pm

Where is 'South Coast'?
Eastbourne here, with a press.
To be fair , any machinist locally would do it for pennies.
Graeme
S4 SE
S2 GTS
Caterham 420R
Sold - Peterson JPS Exige
User avatar
661
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 1271
Joined: 29 Mar 2012

PostPost by: Concrete-crusher » Thu Jan 18, 2018 10:20 pm

I have a press in Romsey if needed

Steve
Concrete-crusher
Third Gear
Third Gear
 
Posts: 402
Joined: 09 Jun 2013

PostPost by: RedBarnMan » Fri Jan 19, 2018 10:29 pm

+1 on the remove rubber with hole saw (I have found my Bosch Progressor hole saws to be good for this) then carefully saw through most of the outer steel bush with an 18tpi hacksaw then they will easily press out. This takes less than 5 minutes per bush. I don't like applying 10T of force to anything unless it is really well supported and designed for that sort of load as you can distort the component and rather than remove the part you end up wedging it in until something goes bang.
RedBarnMan
First Gear
First Gear
 
Posts: 20
Joined: 23 Aug 2013

PostPost by: Chrispy » Fri Jan 19, 2018 11:53 pm

Yep, that's how I've always done bushes in the past - not on Elan's yet but they're nothing special.
Chris
Elan +2 #0245
Exige S2 Supercharged
Chrispy
Third Gear
Third Gear
 
Posts: 331
Joined: 29 Oct 2017

PostPost by: The Veg » Sat Jan 20, 2018 5:03 pm

I've had good result with a cheep Chinese-made 6T press (bought from Harbor Freight, for my fellow Yanks' perspective). It took a little practise to get good result, partly because instead of proper arbors the press just came with a pair of rough-cast iron slabs that don't like to stay put under pressure (C-clamps helped that). I use large sockets to push out the bushes. So far I've only done the front arms with it, but it works a treat now that I've got the hang of it.
Attachments
press.jpg and
1970 Elan Plus 2 (not S) 50/2036
2012 BMW R1200GS
"It just wouldn't be a complete day if I didn't forget something!" -Me
User avatar
The Veg
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 2329
Joined: 16 Nov 2015

PostPost by: 1owner69Elan » Sat Jan 20, 2018 6:44 pm

I opted for an inexpensive bench press. Made bushings and bearing work much easier. Both removal and insertion. I used it a lot when going through everything on my car.

Beats hacking away at things, IMHO.

To quote Brian Buckland(p. 44)

?With a tool like this you can press in water pumps, rear wheel bearings, wishbone Metalastik bushes in fact any force fit component.?

?..., if you do one complete wheel bearing change yourself you will more than pay for it in one single job.?
'69 Elan S4 SE
Street 181 BHP
Original owner
1owner69Elan
Fourth Gear
Fourth Gear
 
Posts: 897
Joined: 16 Jun 2015

PostPost by: mbell » Sat Jan 20, 2018 7:43 pm

The Veg wrote:I've had good result with a cheep Chinese-made 6T press (bought from Harbor Freight, for my fellow Yanks' perspective).


Thanks, that answers something I had been wondering for when I do this job.
'73 +2 130/5 RHD, now on the road and very slowly rolling though a "restoration"
mbell
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 2690
Joined: 07 Jun 2013

PostPost by: Chrispy » Sat Jan 20, 2018 11:12 pm

I have bent suspension arms removing bushes with a press. I prefer to cut them and use the press to install the new bushes.
Chris
Elan +2 #0245
Exige S2 Supercharged
Chrispy
Third Gear
Third Gear
 
Posts: 331
Joined: 29 Oct 2017

Total Online:

Users browsing this forum: No registered users and 23 guests