Bonnet catch - backing plate.

PostPost by: wotsisname » Tue Apr 18, 2017 10:16 am

Hi all,
I was debating whether to fix the bonnet catches [the mechanism that attaches to the engine bay bulkhead] with a backing plate with captive nuts, thinking this would make adjusting the catch easier once the dash is in place.
But then I had a thought - if the bonnet jams (does this happen ?) would it be impossible to release.

- So in short - is this a bad idea ?
1968 Elan plus 2 - project
2007 Elise S2 [modified with a Hethel 70th sticker (yellow)]
2000 Elise S1 - Sold
wotsisname
Third Gear
Third Gear
 
Posts: 487
Joined: 24 Jun 2015

PostPost by: ericbushby » Tue Apr 18, 2017 10:27 am

I did mine the other way round so that if I could not open the bonnet, then I could remove the screws from under the dashboard.
I made a brass clamp plate with two nuts silver soldered on to it which goes on the engine bay side.
Screws and load spreading washers under the dash. I just happened to have the brass sheet.
Just a thought.
Eric in Burnley
1967 S3SE DHC
ericbushby
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 1349
Joined: 13 Jun 2011

PostPost by: KevJ+2 » Tue Apr 18, 2017 11:03 am

I have drilled a hole behind the rear number plate (covered by grommet) in case the rear boot cable malfunctions.
I have also thought about doing the same behind the bonnet catches. A small hole that a small screwdriver can push back each lever from inside the car.
It's my dread that the cable breaks! Has it happened to anyone :?:

Kev.
KevJ+2
Fourth Gear
Fourth Gear
 
Posts: 795
Joined: 23 Aug 2013

PostPost by: ElanDNA » Tue Apr 18, 2017 2:35 pm

ericbushby wrote:I did mine the other way round so that if I could not open the bonnet, then I could remove the screws from under the dashboard.
I made a brass clamp plate with two nuts silver soldered on to it which goes on the engine bay side.
Screws and load spreading washers under the dash. I just happened to have the brass sheet.
Just a thought.
Eric in Burnley
1967 S3SE DHC

Hi Eric
My idea was nearly the same. I made a stainless
steel clamp with two screws weld on them.
Under the dash only washers and stop nuts (stainless all).
For a lot of things I prefer this material.
Urs
Attachments
change-46.jpg and
User avatar
ElanDNA
Second Gear
Second Gear
 
Posts: 119
Joined: 31 Jan 2017

PostPost by: types26/36 » Tue Apr 18, 2017 3:43 pm

Lotus made provision for the bonnet cable breaking and fitted spire clips in order to release the catches.
The spire clips should already be on the cars.
Attachments
bonnet-screws.jpg and
bonnet-screws-2.jpg and
Brian
64 S2 Roadster
72 Sprint FHC
User avatar
types26/36
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 3872
Joined: 11 Sep 2003

PostPost by: prezoom » Tue Apr 18, 2017 3:50 pm

My latches on my Plus2 are attached to a plate on the dash side with threads or captive nuts. There was also a bit of not so robust wood between the latch and the firewall. The wood will be replaced with a piece of white nylon block, milled to the same shape as the deteriorating wood. As I am in the process of re-painting the engine compartment, I left two bolts in place to hold the plates in position, so as to not have to wrestle with holding the plates up under the dash with way too short arms. The nylon blocks will hide the not perfect paint where the bolts were left in place.

With the engine out, I plan on re-installing the latches and adjusting their operating position with relationship to the hood, while the car is on the lift. That way I will have no worries about the dreaded un-latchable hood before the engine and all accessories are back in place.

I do love the dove grey engine compartment, making me wonder if I am going to be happy with the like body color I am applying. Anything will be better than the rattle can flat black that covered everything.
Rob Walker
26-4889
50-0315N
1964 Sabra GT
1964 Elva Mk4T Coupe (awaiting restoration)
1965 Ford Falcon Ranchero, 302,AOD,9",rack and pinion,disc,etc,etc,etc
1954 Nash Healey LeMans Coupe

Owning a Lotus will get you off the couch
prezoom
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 1332
Joined: 16 Mar 2009

PostPost by: wotsisname » Wed Apr 19, 2017 8:53 am

Thanks for your replies, I hadn't appreciated the different parts between the +2 & the elan.
i too am planning to replace the wooden blocks as these are falling apart. I also wish I had done this before fitting the engine.
I like the idea of the captive nuts on the engine side. as the +2 has a three hole arrangement I'm thinking I might use square nuts and/ or a bent washer, so that the nut doesn't just rotate if it is loosened off from the dash side.

Adrian
1968 Elan plus 2 - project
2007 Elise S2 [modified with a Hethel 70th sticker (yellow)]
2000 Elise S1 - Sold
wotsisname
Third Gear
Third Gear
 
Posts: 487
Joined: 24 Jun 2015

PostPost by: Grizzly » Fri Apr 21, 2017 9:15 pm

2 seaters are different catches altogether.

I don't have a picture to hand but on my +2 i just made some plates up the same shape as the flat of the catch (if that makes sense) drilled holes in the correct positions and tacked the heads to the plate with a blob of weld underneath so you can't see it and they don't turn from the engine side.. The wooden blocks do tend to fall to bits but are easy to replace.

lotus-chassis-f36/1974-elan-s130-restoration-stuck-bonnet-t22284.html
Chris
User avatar
Grizzly
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 2020
Joined: 13 Jun 2010

PostPost by: deadline » Sat Mar 02, 2019 5:28 pm

What size screws are used to secure the Bonnet catch to the firewall? I tried 8-32 but they seem to big.
Thanks,
Dan
'65 Elan S1, '66 Elan S3, '66 Elan 26R
Deadline Dan
USA, East Coaster
deadline
First Gear
First Gear
 
Posts: 15
Joined: 07 Jan 2019

Total Online:

Users browsing this forum: No registered users and 16 guests