Lotus Elan

Last of metal bits

PostPost by: jk952 » Fri Jun 29, 2018 1:14 pm

If you see something in the picture you’re interested in send me a note.

Front early version brake pair of castings
Rear brake - damaged at pkg brake but usable
Rear brake one side only
Lotus version cam for dist/fuel pump
Drop links
trans. bracket
Nos iss.18 casting - sold
Head cam caps - sold
Rear seal housing for 6 bolt - sold

Jack

d7b9fd13-098e-4aeb-8b4c-effbcd6ec708.jpeg and
Last edited by jk952 on Tue Jul 03, 2018 11:36 am, edited 2 times in total.
jk952
Third Gear
Third Gear
 
Posts: 283
Joined: 04 Jan 2011
Location: Ont. Canada

PostPost by: Elan45 » Sat Jun 30, 2018 3:57 pm

Where are you located? US or UK?

Is that a jar full of cam caps? Do you have all 10? I have a Weber head that is going to take some TLC to make whole again. It was involved in an accident where the timing chest was broken off the front and I either received it w/o caps or I've lost them in the 30 years I've owned it.

I will be building another TC this fall for my coupe and I'm thinking about converting it from rope seal to lip seal, if I can come up w/ all the parts. I have a crank I would install into the original block so that the numbers would match.So, I am interested in your seal holder.

I might also be interested in the rear caliper, if it is the opposite hand to the one spare I already have. Roger
'67 Elan S3 SS DHC
'67 Elan FHC pre-airflow
'67 Elan S3 SE upgrade to 26R by Original owner
'58 Eleven S2 (ex-works)
'62 20/22 FJ (ex-Yamura)
'70 Elan +2S RHD
'61 20 FJ project
'76 Modus M1 F3
Elan45
Fourth Gear
Fourth Gear
 
Posts: 788
Joined: 23 Nov 2008
Location: Ohio, USA

PostPost by: Elan45 » Sat Jun 30, 2018 4:02 pm

OOps, I didn't see you're Canadian, eh on your signature. Was that there earlier this morning?
'67 Elan S3 SS DHC
'67 Elan FHC pre-airflow
'67 Elan S3 SE upgrade to 26R by Original owner
'58 Eleven S2 (ex-works)
'62 20/22 FJ (ex-Yamura)
'70 Elan +2S RHD
'61 20 FJ project
'76 Modus M1 F3
Elan45
Fourth Gear
Fourth Gear
 
Posts: 788
Joined: 23 Nov 2008
Location: Ohio, USA

PostPost by: jk952 » Sat Jun 30, 2018 4:41 pm

Hi Roger,
Yes have all ten caps. Seal holder is available as are brake bits. Let me know what you want and I will get you a ship cost. Reasonable offer or price.. Send me a pm and will give my normal email, easier than here.
Cheers,
Jack
Last edited by jk952 on Sun Jul 01, 2018 12:40 pm, edited 1 time in total.
jk952
Third Gear
Third Gear
 
Posts: 283
Joined: 04 Jan 2011
Location: Ont. Canada

PostPost by: jk952 » Sat Jun 30, 2018 5:22 pm

Roger,
hmmm.. noticed people’s location is only shown if you are logged in..lol
jk952
Third Gear
Third Gear
 
Posts: 283
Joined: 04 Jan 2011
Location: Ont. Canada

Total Online:

Users browsing this forum: No registered users and 3 guests