problem with brake disc clearance

PostPost by: wondo » Wed Jun 27, 2007 8:33 pm

hi,

i`m assembling my new spyder chassis and wishbones etc. at the moment, and i`m having a little problem with the brake discs hitting the lower wishbone and not sitting right in place in the brake caliper.

please take a look...


Attachments
DSC00258.jpg and
DSC00255.jpg and
wondo
First Gear
First Gear
 
Posts: 18
Joined: 21 Aug 2006

PostPost by: Foxie » Thu Jun 28, 2007 4:41 pm

Is this on one side only ? If so measure up both sides to identify the problem. Then get on to Spyder.

I had to cut off and reweld the shock bracket on my Spyder rear hub. Obviously a Monday morning job.

Sean Murray
User avatar
Foxie
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 1630
Joined: 20 Sep 2003

PostPost by: wondo » Thu Jun 28, 2007 5:11 pm

it`s exactly the same on both sides, that`s what makes me wonder if there is a problem with the hubs.
i could get rid of it by adding a washer under the brake disc, but i would like to solve it without fumbling around on an important part like the brakes...
wondo
First Gear
First Gear
 
Posts: 18
Joined: 21 Aug 2006

PostPost by: frearther » Thu Jun 28, 2007 5:29 pm

I swapped out my old (limited motion) style bushings for poly bushings, and this gave the rear suspension a much greater range of motion - so much so, that I had the same problem. I fabricated limit straps with wire rope and appropriate fittings. You may have to do the same. Id send you a picture if I knew how.
Art Frederick
S2 Roadster, built in 1965, registered in 1966, No. 26/4934
Nothing else of interest at present
User avatar
frearther
Fourth Gear
Fourth Gear
 
Posts: 501
Joined: 23 Sep 2003

PostPost by: elansprint71 » Fri Jul 13, 2007 2:33 pm

This is how mine looked when it went together; I suggest that you ring Spyder and speak with Wiggy.[/img] It's a Sprint but I guess the +2 has similar clearances.

Cheers,
Pete.
Attachments
drive shafts 2 copy.jpg and
User avatar
elansprint71
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 4435
Joined: 16 Sep 2003

PostPost by: gerrym » Fri Jul 13, 2007 3:55 pm

Wondo, I had exactly the same issue as you (disk brake touching wishbone on full droop.
I initially resolved the problem by shimming (washers) the disk further out from the hub), then checking fro run-out of the disk of course. I also had a very light touch between bottom of handbrake and wishbone (one side only - presumed tolerance build up).
My longer term solution may be to return coil-overs to Protech and get the travel reduced.

Query, does any one know what spring compressor can be used on the coilover units with 1.9ID springs
Gerry
gerrym
Fourth Gear
Fourth Gear
 
Posts: 894
Joined: 25 Jun 2006

PostPost by: Jason1 » Sat Jul 21, 2007 5:10 pm

Hi Guys

I was pulling a few parts out of my shed and noticed the difference in thickness of these 2 discs. I bought these discs assembled on 2 rear struts second hand from the same 1973 +2.

This maybe the cause of the problem, maybe the new supply discs are just too thick??

Jason
Attachments
rear disks.jpg and
User avatar
Jason1
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 1554
Joined: 03 Nov 2005

PostPost by: frearther » Sat Jul 21, 2007 5:50 pm

Gerry,

I assume you're referring to the rear springs, since the discussion has been about clearances in the rear. You don't need to use a spring compressor back there; jacking up the strut from the bottom of the hub (with suitable cushioning) will allow you to remove the castle nut. Then, slowly let the jack down, and the spring will decompress as the hob goes down.

Be sure that you jack up the car by the frame before you do this, of course.
Art Frederick
S2 Roadster, built in 1965, registered in 1966, No. 26/4934
Nothing else of interest at present
User avatar
frearther
Fourth Gear
Fourth Gear
 
Posts: 501
Joined: 23 Sep 2003

PostPost by: gerrym » Wed Jul 25, 2007 9:15 am

Art, discussion and photos have referring to Spyder RSC rear suspenion with coil overs not struts.
Regards
gerrym
Fourth Gear
Fourth Gear
 
Posts: 894
Joined: 25 Jun 2006

PostPost by: frearther » Wed Jul 25, 2007 11:56 am

OOps! :oops:
Art Frederick
S2 Roadster, built in 1965, registered in 1966, No. 26/4934
Nothing else of interest at present
User avatar
frearther
Fourth Gear
Fourth Gear
 
Posts: 501
Joined: 23 Sep 2003

PostPost by: kneedham » Mon Apr 08, 2019 10:15 am

Rather late reply but I had the same issue whilst building the Spyder rear suspension.
I found that I had put the driveshaft side bearing in the housing the wrong way round. The bearing has a lip on the inner race that means the disc mount is nearer to the diff. Turn the bearing around, problem solved.
kneedham
New-tral
 
Posts: 6
Joined: 22 Apr 2012

Total Online:

Users browsing this forum: No registered users and 25 guests