Best new jack to use

PostPost by: Iyarno » Sat Aug 31, 2013 10:06 am

I'm after a new reliable jack which can be stored in the boot and used for light use such as changing wheels.

I know the original type was a scissor jack with a round jacking point attached but these don't seem to be available. The only jack with a suitable jacking point is a bottle jack. These seem OK, but I have a 2-ton which doesn't have enough height, and a 4-ton which doesn't fit until you lift the other side a bit with the 2-ton. Does that make sense? Anyway it's a complete faff and there must be a better solution.

What *new and easily available* jacks are people using?

Cheers, Ian
User avatar
Iyarno
Second Gear
Second Gear
 
Posts: 155
Joined: 21 Aug 2010

PostPost by: worzel » Sat Aug 31, 2013 11:11 am

Hi

I got hold of an as new jack from a scrapped Nissan Micra for ?5. To improve stability I had the base of the jack welded to a foot square metal plate (handy for soft ground too).

OK- it's heavy and I have mine securely fastened down in the boot but it sure is a lot safer than some I've seen.

Regards

John
worzel
Fourth Gear
Fourth Gear
 
Posts: 626
Joined: 13 Jan 2004

PostPost by: billwill » Sat Aug 31, 2013 2:51 pm

I usually use one of these double-scissor type.
Image

They are very low when down and fit under anything; yet they lift quite high.


I don't know where you can get one though.

This one looks nice, it seems to have an electric motor to do the hard work.
Image

But the Australian article containing that photo, does not say where you can get one. It is a warning about accidents with car-jacks.


This was on a foreign eBay, but the auction had expired, but it gives more detail of such an electric double-scissor jack.

http://www.bidorbuy.co.za/item/92705368 ... utton.html


You should be able to find a supplier of almost any kind of jack by choosing & clicking on these pictures.

https://www.google.com/search?q=car+jac ... B591%3B591
Bill Williams

36/6725 S3 Coupe OGU108E Yellow over Black.
billwill
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 5060
Joined: 19 Apr 2008

PostPost by: billwill » Sat Aug 31, 2013 3:35 pm

I found these cartoons in my browsing.

http://www.cartoonstock.com/directory/c/car_jack.asp
Bill Williams

36/6725 S3 Coupe OGU108E Yellow over Black.
billwill
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 5060
Joined: 19 Apr 2008

PostPost by: worzel » Sat Aug 31, 2013 4:11 pm

Hi

The Nissan one looks pretty much like the one illustrated. Forgot to add- I made a small wooden pad/block with a recessed part to fit the saddle of the jack. Covered the upper face with thick rubber and this is used under the corner of each sill.

Regards

John
worzel
Fourth Gear
Fourth Gear
 
Posts: 626
Joined: 13 Jan 2004

PostPost by: Paul Chapman » Sun Sep 01, 2013 8:22 am

I use a Ford sill jack ( Mk5 Escort ) plus a 10mm ply pad fitted with a strip of 'T-bar' to engage in the slot in the business end of the jack. This has the advantage of all fitting in the rear wing well next to the fuel tank along with a dead blow hammer for removing / refitting the spinners.

I can take no credit for this as it was the idea of a fellow club member.
Paul
Paul Chapman
Second Gear
Second Gear
 
Posts: 117
Joined: 19 May 2009

PostPost by: gino1 » Thu Sep 12, 2013 1:12 pm

Hi, I also use a scissor type jack that can be found at the local scrapyards for next to nothing.
I have welded a metal plate on the top to avoid the top part damaging the underside and even penetrating through the floor :?
Works great,
Gino
Milano
italy
1964 Elan S2 Roadster
1965 Elan S2 Roadster
1965 Elan S3 Coupe
1968 Elan S4 Coupe
1969 Elan +2
1968 Lotus Seven S3
1982 Lotus Esprit S3
1961 Ford Anglia
2000 Lotus Elise Motorsport-56
User avatar
gino1
Fourth Gear
Fourth Gear
 
Posts: 514
Joined: 12 Sep 2003

Total Online:

Users browsing this forum: No registered users and 5 guests