How best to affix "things" to the body?

PostPost by: steve lyle » Sat Aug 10, 2019 4:17 am

I'm working on rewiring my Elan Sprint. I'm basically rebuilding/restoring/upgrading the dash and engine harnesses.

One thing I've run into, several times, is how to best attach components to the body. For instance, I'm adding a modern fuse box, and putting it on the horizontal surface where the voltage regulator was originally (the car now has an alternator). How best to attach it? I'd rather not have to ask for help, and my arms aren't 6 feet long or come with two elbows each, so through bolting wasn't an option. If it was a metal car I might consider short sheet metal screws. What I ended up doing in this case was cut a strip of light sheet metal, drilled holes in it to match the fuse box attachment holes, then welded nuts on it over the holes. Then I taped it temporarily to the top/underside of the footwell, and bolted the fuse box to it.

It was a fair bit of work. Is there an easier/quicker way?

I've got other things I need to attach, primarily zip tie mounts to secure the harness. I'd rather not use the original types that require a 1/4" hole.

Thanks,
Steve
Steve Lyle
1972 Elan Sprint 0248k @ https://www.mgexp.com/registry/1972-Lot ... 48K.30245/
1972 MGB Roadster @ https://www.mgexp.com/registry/1972-MG- ... 842G.4498/
2007 BMW 335i Coupe
User avatar
steve lyle
Third Gear
Third Gear
 
Posts: 454
Joined: 15 Jun 2015

PostPost by: oldelanman » Sat Aug 10, 2019 6:00 am

Lots of options ........ rubber nuts, jack nuts, versa nuts, nutserts, rivnuts etc. A Google search should find something suitable.
Roger
S4 DHC
oldelanman
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 1967
Joined: 02 Jan 2008

PostPost by: wotsisname » Sat Aug 10, 2019 6:41 am

Peel rivets ? - if you can't see the end result on the "blind side" and don't want to remove the item often.. most other options tend to need a biggish hole. Scrivets are used on many moderns.
1968 Elan plus 2 - project
2007 Elise S2 [modified with a Hethel 70th sticker (yellow)]
2000 Elise S1 - Sold
wotsisname
Third Gear
Third Gear
 
Posts: 487
Joined: 24 Jun 2015

PostPost by: 1owner69Elan » Sat Aug 10, 2019 6:49 am

I?ve had some success using automotive plastic push fasteners. Certain types are easy to undo as well. Available in a lot of sizes and shapes. Check Amazon.

6ed4294a-8a4d-4ea0-8800-b1944c169821.jpeg and
'69 Elan S4 SE
Street 181 BHP
Original owner
1owner69Elan
Fourth Gear
Fourth Gear
 
Posts: 897
Joined: 16 Jun 2015

PostPost by: grassyknoll » Sat Aug 10, 2019 9:24 am

+1 plastic push fasteners as used in anything modern, dont corrode and are flexible so heat expansion wont cause spidercracks
grassyknoll
First Gear
First Gear
 
Posts: 36
Joined: 30 Jul 2015

PostPost by: DavidLB » Sat Aug 10, 2019 5:31 pm

I used rivinuts on my +2. Workvery well in my experience
David
DavidLB
Second Gear
Second Gear
 
Posts: 217
Joined: 23 Apr 2010

PostPost by: vincereynard » Sat Aug 10, 2019 7:52 pm

Another vote for (aluminium) rivnuts. Wiring / fuel pipe / rear number plate! Etc Etc.

Use a washer to spread the load on thin fibreglass.
vincereynard
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 1240
Joined: 12 Jan 2015

PostPost by: el-saturn » Sun Aug 11, 2019 7:18 am

these buggers are excellent for your issue: best results when laminated to the surface in question - i've still got loads of round ones (M6 and M8) - i could mail you some sandy (mine are females)
Attachments
befestigungselemente-elan.jpg and
el-saturn
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 1374
Joined: 27 Jun 2012

PostPost by: steve lyle » Mon Aug 12, 2019 5:02 pm

Thanks, everybody. Sounds like I need to find a source for Rivnuts for what I'm doing now.

The plastic connectors are a good idea too, for lighter loads.

Regards,
Steve
Steve Lyle
1972 Elan Sprint 0248k @ https://www.mgexp.com/registry/1972-Lot ... 48K.30245/
1972 MGB Roadster @ https://www.mgexp.com/registry/1972-MG- ... 842G.4498/
2007 BMW 335i Coupe
User avatar
steve lyle
Third Gear
Third Gear
 
Posts: 454
Joined: 15 Jun 2015

PostPost by: SENC » Tue Aug 13, 2019 1:41 am

When I was looking a while back, someone recommended Marson. I bought their 39302 kit on Amazon, along with some aluminum rivnuts. Has been a nice thing to have, and worked well.
Henry
69 Elan S4
65 Seven S2
SENC
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 1058
Joined: 30 Dec 2015

PostPost by: steve lyle » Tue Aug 13, 2019 2:05 am

Steve Lyle
1972 Elan Sprint 0248k @ https://www.mgexp.com/registry/1972-Lot ... 48K.30245/
1972 MGB Roadster @ https://www.mgexp.com/registry/1972-MG- ... 842G.4498/
2007 BMW 335i Coupe
User avatar
steve lyle
Third Gear
Third Gear
 
Posts: 454
Joined: 15 Jun 2015

PostPost by: SENC » Tue Aug 13, 2019 2:30 am

Henry
69 Elan S4
65 Seven S2
SENC
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 1058
Joined: 30 Dec 2015

PostPost by: Grizzly » Tue Aug 13, 2019 12:45 pm

I wouldn't use anything that expands (like Rivnuts) they are great in steel but less than ideal in grp. If your going to use Rivnuts in GRP make sure they are the peeling type.
rivnut-pn-blind-rivet-nut-with-slotted-slank-1.jpg and


When i did it i just super glued some single side spire clips the back of the hole and ran a self tapper through. You can also drill the holes for the fuse box, put the box in place with the screws just pushed through the holes, get on the other side and wind the spire clip as for as poss then tighten the rest of the way from the outside via the screw head (if that makes sense)
Chris
User avatar
Grizzly
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 2020
Joined: 13 Jun 2010

PostPost by: el-saturn » Tue Aug 13, 2019 4:16 pm

we (25 blokes) worked at my company nobrac (carbon backwards) in the late 70s and 80s - the solution i showed was used in many a famous car - either laminated on or glued with epoxy! simple, lots of surface to distribute the load and easy to change if something went wrong - if you've ever worked in composites youll know what im talkin about sandy
el-saturn
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 1374
Joined: 27 Jun 2012

PostPost by: 661 » Tue Aug 13, 2019 5:36 pm

el-saturn wrote:these buggers are excellent for your issue: best results when laminated to the surface in question - i've still got loads of round ones (M6 and M8) - i could mail you some sandy (mine are females)


I've used a number of these, often removing the nut/threaded rod and replacing with a welded imperial sized stainless version.
I attach them with 2 pack adhesive, immensely strong.
Graeme
S4 SE
S2 GTS
Caterham 420R
Sold - Peterson JPS Exige
User avatar
661
Coveted Fifth Gear
Coveted Fifth Gear
 
Posts: 1271
Joined: 29 Mar 2012

Total Online:

Users browsing this forum: No registered users and 15 guests